How to Measure for Tall Boots
You'll need a helper and a cloth measuring tape to take accurate measurements.

• Wear the breeches and socks that you're most likely to wear with your new boots.
• Sit in a straight chair with your stocking feet flat on the floor and knees at a 90 degree angle.
• For calf width, have your helper measure the circumference of your calf at its widest point.


Note: Do not add increments to your calf measurement. Boot leather stretches as it breaks in. New boots should fit snugly and should be slightly difficult to put on. If the boots are too large when you purchase them, they will only become looser over time and will increase the risk of the boot dropping too much resulting in a shortened height.


• For boot height, have your helper measure from the floor to the back of your knee.

Boot height is a matter of personal preference. Some riders prefer a very tall boot, while others prefer a shorter boot. In general, for field boots you'll want to add 1 1/2 to 2 inches to your height measurement. For a moderately stiff dressage boot, you'll want to add 1 1/4 to 1 1/2 inches. Also, check the riding boot size chart on the ordering tab for your desired brand of boots to determine whether you should make any specific height adjustments.



Note: Styles in both field and dress boots that feature a Spanish top help to create an elongated look as up to 1 to 1 1/2 inches of curved leather is added to the outside of the top of the boot. A Spanish top is cut higher and more curved than a regular boot top.




• Match your calf width and height measurements to the riding boot sizing chart pertaining to the brand of boot you wish to order.

If you're considering zippered boots, look for a calf measurement that is as close to or a smidge over your measurement to avoid stressing the zippers. If your calf measurement is as little as 1/8 inch wider than the calf measurement listed for your expected size, you may want to consider the next size up or you may have problems with the boot zippers. If the next size up seems as though it will be too wide for your calf and the boot would be too loose, then consider another boot that will fit your leg better. It is not uncommon when choosing from stock tall boots for riders to consider all size charts and all manufacturers to find their optimal boot.

Shoe size pertains to your usual size for footwear. Some riders choose to go up a foot size if their desired boot height is not available with their regular size. Extra space in the foot can be taken up with an extra foot bed, gel sole or air cushion.

Note: For boots that are offered in whole foot sizes, factor the type of sock you plan to wear into your decision. For example, if you normally wear size 7 1/2 shoe but the boot you wish to order is offered in whole sizes, the thickness of your socks will determine the correct size to order. For heavy, thick socks, you would choose a size 8; for average, thin socks you would choose a size 7.

Tack Cleaning and Leather Care

Think of your tack as an investment. You've spent time and money in selecting the best quality leather goods for you and your horse. With diligent and correct leather care, including proper tack and leather storage, you can get the maximum return on your investment through its long and safe use.

Saddles, Bridles, Martingales, Breastplates and Girths

Leather is skin. Just as your skin suffers abrasions and dryness from irritants like sweat and dirt, your leather does too. The key to tack longevity is the practice of daily leather cleaning after every ride.

The traditional method of leather care is to wipe dust and sweat from your tack immediately after use with a sponge or cloth that is barely moistened with cool water. Then rub a thin layer of glycerin soap on the leather to seal the pores and keep it soft but not sticky. Newer methods involve convenient and easy-to-use leather cleaning and conditioning products, a wide array of which exists on the market today. You can choose from one-step cleaning and conditioning creams or two-step systems with a cleaning solution followed by a conditioning agent that restores moisture.

Note: Almost every saddle and tack manufacturer has a recommendation or product preference for leather cleaning and conditioning products. Some tack manufacturers produce their own products. Always follow manufacturer's guidelines when considering commercial leather cleaners and conditioners.

Be sure to clean the parts of your tack that are under pressure during use or where sweat or saliva may collect. These areas include the curves near buckles where reins and cheek pieces attach to bit rings, all parts of girths, billet straps and the creases in stirrup leathers where irons rest. The cleaning process is also a good time to check that stitching is tight and intact, and that the leather has not ripped or cracked.

For tack that has been neglected over time or that is extremely dirty, use warm water and a soft brush to remove collected grime. You may choose to use a pH-balanced cleaner, such as Lexol Cleaner. Because warm water is extremely drying to leather, immediately follow it with a fine layer of glycerin soap or a leather conditioner, such as Lexol Conditioner.

Very dry leather may need to be treated on its underside with a thin coat of warmed Neatsfoot Oil, or fed with a thick saddle food such as Effax Lederbalsam, Passier Lederbalsam or Stubben Hammanol.

Leather Storage
Leather tack can be attractive to rodents when food sources are scarce. Try to secure your tack room from these unwanted visitors. Tack is best maintained with daily use and cleaning. However, if your tack has to be stored for an extended time, try to place it in a temperature-controlled environment. Extreme cold and heat are detrimental to leather.

Cover stored tack in fabric or newspaper so the leather can breathe rather than in plastic that does not allow air to circulate. Be sure to check your unused equipment occasionally for mildew, and remember to condition it regularly to prevent it from drying out.

Bit Care and Cleaning
Rinse your bit in water or wipe it thoroughly after every use. Dried food particles on a bit are abrasive to your horse's mouth. Additionally, it is far easier to clean a bit on a regular basis rather than scrubbing off accumulated grime.

Over time, bits may become tarnished from use and storage. Products on the market, such as Herm Sprenger Diamond Paste or Nevr-Dull Wadding Polish, remove layers of tarnish. Non-toxic, non-acidic and developed for use on mouthpieces and all types of metal, HS Diamond Paste helps prevent tarnish from recurring. (You can also use it on your spurs and metal stirrup irons!) Nevr-Dull is easily used by pulling a wad of the saturated cloth from the tin and rubbing until black can no longer be seen on the cloth. Wash the mouthpiece thoroughly to remove any trace of the product after polishing.

Synthetic Saddles, Halters and Horse Boots
To clean a synthetic saddle, use a mixture of gentle soap and warm water. You can soak smaller synthetic articles like nylon halters or neoprene splint boots in a gentle soap and warm water solution to loosen grime. Stuck on dirt can sometimes be removed with a soft brush while the item is still wet. Rinse or hose thoroughly, and allow the items to dry naturally in the sun.